-
- News
- Books
Featured Books
- design007 Magazine
Latest Issues
Current IssueLevel Up Your Design Skills
This month, our contributors discuss the PCB design classes available at IPC APEX EXPO 2024. As they explain, these courses cover everything from the basics of design through avoiding over-constraining high-speed boards, and so much more!
Opportunities and Challenges
In this issue, our expert contributors discuss the many opportunities and challenges in the PCB design community, and what can be done to grow the numbers of PCB designers—and design instructors.
Embedded Design Techniques
Our expert contributors provide the knowledge this month that designers need to be aware of to make intelligent, educated decisions about embedded design. Many design and manufacturing hurdles can trip up designers who are new to this technology.
- Articles
- Columns
Search Console
- Links
- Events
||| MENU - design007 Magazine
Design for Profitability: Avoiding Fabrication Issues and Minimizing Costly Revisions
July 31, 2013 | Mark Thompson, CID, Prototron CircuitsEstimated reading time: 1 minute
Note that I use the term “design for profitability,” or DFP, as opposed to any of the other acronyms such as DFM (design for manufacturability), DFT (design for test), or DFA (design for assembly). I’m taking this approach because it really all comes down to profit, doesn’t it?
Designers have the power to design profit into the board, or, conversely, inadvertently increase costs and remove profit from the PCB. In this article I am going to go over just a few of the challenges that fabricators routinely face and some typical solutions, especially solutions that can affect your bottom line.
I will start with DFM. Generally, this is the first stage for prototyping and DFM depends greatly on the capabilities of your chosen fab shop. Some designs are finished with autorouters after the critical traces have been hand-placed. It is at this point that unintended issues can arise between design and fab.
An example of this is same net-spacing violations where a track may “double back” near a surface mounted component, creating same-net spacing violations (Figure 1). Whereas the software does not see these as legit violations because they are same net, a fabricator knows that any features creating spaces below 0.003” can easily flake off at the image stage and create havoc elsewhere in the form of shorts. Edit time must be taken at the fab stage when these same-net spacing violations occur and the slivers eliminated. Some CAM software packages have a sliver fill option, but again this requires additional edit time at CAM.
Read the full article here.
Editor's Note: This article originally appeared in the March 2013 issue of The PCB Design Magazine.
Suggested Items
Real Time with... IPC APEX EXPO 2024: Exploring IPC's PCB Design Courses with Kris Moyer
04/18/2024 | Real Time with...IPC APEX EXPOGuest Editor Kelly Dack and IPC instructor Kris Moyer discuss IPC's PCB design training and education offerings. They delve into course topics such as design fundamentals, mil/aero, rigid-flex, RF design, and advanced design concepts. They also highlight material selection for high-speed design, thermal management, and dissipation techniques. The interview wraps up with details about how to access these courses online.
Cadence Unveils Palladium Z3 and Protium X3 Systems
04/18/2024 | Cadence Design SystemsThe Palladium Z3 and Protium X3 systems offer increased capacity, and scale from job sizes of 16 million gates up to 48 billion gates, so the largest SoCs can be tested as a whole rather than just partial models, ensuring proper functionality and performance.
Signal Integrity Expert Donald Telian to Teach 'Signal Integrity, In Practice' Masterclass Globally
04/17/2024 | PRLOGDonald Telian and The EEcosystem announce the global tour of "Signal Integrity, In Practice," a groundbreaking LIVE masterclass designed to equip hardware engineers with essential skills for solving Signal Integrity (SI) challenges in today's fast-paced technological landscape.
On the Line With... Podcast Talks With Cadence Expert on Manufacturing
04/18/2024 | I-Connect007In “PCB 3.0: A New Design Methodology: Manufacturing” Patrick Davis returns to the podcast to talk about design rules. As design considerations become more and more complex, so, too, do the rulesets designers must abide by.
Designing Electronics for High Thermal Loads
04/16/2024 | Akber Roy, Rush PCB Inc.Developing proactive thermal management strategies is important in the early stages of the PCB design cycle to minimize costly redesign iterations. Here, I delve into key aspects of electronic design that hold particular relevance for managing heat in electronic systems. Each of these considerations plays a pivotal role in enhancing the reliability and performance of the overall system.